I started with a V0.0 Kit from Aliexpress (now it's 0.1, which is better in any respect)*:
Formbot Voron V0.1 Kit (AliExpress) https://bit.ly/39kfWdC
LDO Voron V0.1 KIT (Caribou3D) https://bit.ly/3KBxqzL

Recommended Kits for bigger DIY printers:
Voron 2.4 Kit (AliExpress) kit bit.ly/3PklmWE
Voron Trident Kit (AliExpress) https://bit.ly/3yxMaNe

STL files, instructions and BOM on the recent upgrades:
https://247printing.gumroad.com/l/247zeroBeta1

Support my work at Patreon:
https://www.patreon.com/247printing

My Instagram and Twitter - more about my doings and behind the scenes:
Instagram: https://www.instagram.com/247printing/
Twitter: https://twitter.com/247_printing

Watch the print at 1100mm/s:
https://youtube.com/shorts/oy9C-VDsu-k?feature=share

💚Pizza, Beer and Coffee helps me going on💚
https://paypal.me/247printing
💚Thanks to all who support/ed my work💚


---------------Settings:

Filament: ESUN ABS+ - a great choice filament for strong parts and easy printing
https://amzn.to/3Bi0x7k

T_Hotend = 290C
T_Bed = 90C

Requested Speed: 1000mm/s
Acceleration: 35.000 mm/s²
square_corner_velocity: 15mm/s
Nozzle: 0.4mm
Layer Height: 0.1mm
Line width: 0.4mm
Volumetric flow: 40mm³/s
Lengths of straights: 65mm
Lengths of printing @ REAL 1000mm/s: 35mm

Xxxx ALL DESIGNS AVAILABLE SOON xxxX
@ Voron Users / Thingiverse



*******UPGRADES* STAGE 1 on my Voron V0 - VIDEO DEEP DIVES and ANALYSES incoming:

For years now, I use BigTreeTech/BIQU products - very much recommended:
(I was sponsored with an Octopus Board V1.1, TMC2209, 70W Heater and PT1000 thermistor)
Get the Octopus Board here:
https://bit.ly/31kKCrj

—MOTION (Part 1: Video Deep Dive incoming)

Nema14 spec Voron V0.1 @1.7A (OMC 14HS20-1504S)
https://amzn.to/3kBO5tm

F623 bearings instead of toothed idlers
https://amzn.to/2UktSgZ

WD40 specialist dry lubricant for rails (PTFE)
https://amzn.to/3ziGaF4

Gates-LL-2GT 6mm belts
https://amzn.to/3kCaAht


— EXTRUSION: (Part 2: Video Deep Dive)
Slice Engineering Mosquito Magnum (5% off!): https://www.sliceengineering.com?p=rkjO5IsbY

VolcoMosq Block (+9mm melt): https://www.youtube.com/watch?v=_2xph8QkcpU&t=18s

E3D Hemera (Bowden config)
https://amzn.to/3zdvAzk

Capricorn Bowden Tube
https://amzn.to/3kBrgWE

50W heater (24V)
https://amzn.to/2UmOIwa

PT1000 temp sensor
https://amzn.to/3ivfdY2

Boron Nitride Paste @ heater, thermistor and heat break
https://amzn.to/3kvPem6


— COOLING (Part 3: Video Deep Dive)
4010 blower fans (24V), updated toolhead
https://amzn.to/3irazKT

optimized air ducts for part cooling with aluminium tape insulation
https://amzn.to/3zhbuEs

External Static Cooling: 4x4020 fans (24V)
https://amzn.to/3zcap0D

4x40mm heatsink at AB stepper motors
https://amzn.to/3irvLAh

2x 4020 / or 4010 fans (5V) at heat sinks (stepper motors)
https://amzn.to/3wOmfMJ

25mm axial fan (5V) for stepper drivers
https://amzn.to/3eDf4AW


— Software / Firmware / Controllers (Part 4: Video Deep Dive):

Klipper
https://www.klipper3d.org/

Raspberry Pi Zero W (Mainsail)
https://amzn.to/3xR9l21

Raspberry Pi 3B (Input Shaping and Octoprint)
https://amzn.to/2UwIMAu

Alternative: Raspberry Pi4:
https://amzn.to/3kBt4io

Simplify 3D: multi processes used
https://www.simplify3d.com/


-------------------------------------------------------
My modest video gear*:

iPhone 11 Pro: https://amzn.to/2VZYswJ
Smartphone video rig: https://amzn.to/3iriub5
GoPro Hero 9: https://amzn.to/2UZI9Q5
FLIR ONE PRO: https://amzn.to/2UWAe67
Similar to the soft boxes I use: https://amzn.to/3xRes2d
Similar to the tripod I use: https://amzn.to/2V1I6mw

*Amazon links are affiliate links at no extra costs for you!

#JoinTheSpeed
#247printing
#volcomosq
#SpeedBoatRace