♫musicjinni

Creality Ender 3 V2 - Simple Tips for Super Clean 3D Prints

video thumbnail
Are you struggling to get the right settings for your 3D prints? If you have stringing, blobs and other irregularities this video will show you the simplest methods along with a few other useful tips which can take your prints to the next level.

If you'd like to become a patron to help this channel grow and get involved with future video ideas, here is the link: https://www.patreon.com/Needitmakeit

Recently I've also discovered a feature within Cura which gives your printer the ability to print multiple parts at once all while keeping your prints looking great with no added time.

For reference, I like to keep my printer as close to stock as possible. I have had problems with the extruder side Bowden fitting and have replaced the tube and the fitting as well. That is covered in a separate video. I've also upgraded to stiffer bed springs to apply a little more pressure on the leveling knobs in hopes to not have to re-level the bed (so far so good).

As mentioned in the video, here are the important settings for each test:

Printed on glass build plate with dollar store glue stick
All prints with 0.6mm nozzle
I use this glass https://amzn.to/2KyLCjO after my original glass had a chunk removed

Test #1
Red PETG
Layer Height 0.16mm, Wall Lines 4, Bottom Layers 5, Top Layers 6, Pattern Zig Zag, Infill 35% Cubic, 225C Nozzle, 75C Bed, 78mm Infill, 37mm Outer Wall, 57mm Inner Wall, 55mm Top/Btm, 45mm Initial Layer, 4mm Retraction, Combing Off, Print All At Once, Cooling Fan 8%, Seams Manually Aligned

Test #2
Red PETG
Layer Height 0.16mm, Wall Lines 4, Bottom Layers 5, Top Layers 6, Pattern Zig Zag, Infill 35% Cubic, 225C Nozzle, 75C Bed, 78mm Infill, 37mm Outer Wall, 57mm Inner Wall, 55mm Top/Btm, 45mm Initial Layer, 4mm Retraction, Combing On, Print All At Once, Cooling Fan 100%, Seams Manually Aligned

Test #3
Red PETG
Layer Height 0.1mm, Wall Lines 4, Bottom Layers 5, Top Layers 6, Pattern Zig Zag, Infill 35% Cubic, 225C Nozzle, 75C Bed, 78mm Infill, 37mm Outer Wall, 57mm Inner Wall, 55mm Top/Btm, 45mm Initial Layer, 4mm Retraction, Combing On, Print All At Once, Cooling Fan 100%, Seams Random

Test #4
Red PETG
Layer Height 0.2mm, Wall Lines 4, Bottom Layers 5, Top Layers 6, Pattern Zig Zag, Infill 35% Cubic, 225C Nozzle, 75C Bed, 78mm Infill, 37mm Outer Wall, 57mm Inner Wall, 55mm Top/Btm, 45mm Initial Layer, 4mm Retraction, Combing On, Print All At Once, Cooling Fan 100%, Seams Random

Test #5
Black Carbon Fiber PETG
Layer Height 0.16mm, Wall Lines 4, Bottom Layers 5, Top Layers 6, Pattern Zig Zag, Infill 35% Cubic, 225C Nozzle, 75C Bed, 78mm Infill, 37mm Outer Wall, 57mm Inner Wall, 55mm Top/Btm, 45mm Initial Layer, 4mm Retraction, Combing On, Print All At Once, Cooling Fan 100%, Seams Manually Aligned

It can take up to 2 weeks and 40 hours to make a short video like this, If you would like to support the channel, these are affiliate links, I receive a small % of the sale.

NEW MIC (I bought this)
https://amzn.to/3vcMKAr - Rode Wireless ME mic (Saved me about 4+ hours/vid)
https://amzn.to/3NBFvZe - Mag clip (Super handy, but a little pricy)

BAMBU PRINTERS
https://shrsl.com/4aghz

CREALITY PRINTERS
https://shrsl.com/4aghy

CREALITY HYPER PLA
https://shrsl.com/4aghn

I mention Octoprint and Spaghetti detective in the video because it is one of the best additions to my 3D printer yet, I do not check on my prints anymore, if I want to see the progress, I just check the app. If you print any type of production volume I can definitely recommend this, if you only print a little bit, it is nice to have, but not a necessity.

If you are struggling with problems and you need help, send me an email or write in the comments.

#ender3
#3dprinting
#Problemsolving

Creality Ender 3 V2 - Simple Tips for Super Clean 3D Prints

Creality Ender 3 V2 - Stop Stringing, Improve Print Quality & Time With These Two Settings

Say Goodbye To Stringing Forever - 3D Printing Tips!

Creality Ender 3 V2 - An Even Cleaner Print By Using This Cheat

Stop Stringing With These Retraction Settings

The Ultimate Guide to Perfect 3D Prints

Creality Ender 3 V2 - My Cleanest Print Ever and You Can Too!

How to Control Seams In Cura Slicer Settings

So Smooth... Ironing Settings in Cura for Perfect Top Layers - 3D Printer Pro Tips

Creality Ender 3 V2 - Fixing the Hidden Problem that Can Cause Stringing and Unresponsiveness

3D Printer Blobs: a mysterious problem you won't guess how to fix 🤔

The secret to 3D printing PETG [Adventurer 4]

Better Organic Supports for your 3D Prints

Creality Ender 3 V2 - Speed up prints without sacrificing quality by turning on this setting

3D Printed Pin Support Challenge 😱

Hide Gaps in 3D Prints with Cura Slicer Settings

How to Smooth PLA 3D Prints to Look Like Resin!

Understanding Top and Bottom Layers: The Key to Perfecting Your 3D Prints

printed WITHOUT support #shorts

Creality Ender 3 V2 - Stop The Print From Failing Like This

Creality Ender 3 V2 - Speed up prints without sacrificing quality by identifying and changing...

Creality Ender 3 V2 - No More Movement at the Bowden Tube Fitting to Extruder By Doing This!

Fail Print on Elegoo Neptune 4 max #3dprinting #3dprinter #memes #viral

3D Printing in Night Mode 😙 #3dprinting #upgrade #3d

SMOOTHING 3D prints with isopropyl alcohol

Creality Ender-3 S1 - 3D Printer - Unbox & Setup

Fine Tuning Retractions And Coasting With ideaMaker

Creality Ender 3 V2 - What Happens when Printing with Bad Filament Feat. Bambu Carbon X1C

Creality Ender 3 V2 - The quest for the best build-plate adhesion for ABS

Cleaner Top Layers Using Monotonic Ordering In Cura! (With & Without Ironing)

Disclaimer DMCA